Snapshot OK on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave Multitap Transformer Replaceable Fuse User Serviceable Duty Cycle Q-Spot 15
DMX DATA CABLE Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications. Standard microphone cables cannot tr
Setting up a DMX Serial Data Link 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the controll
Mounting ORIENTATION This fixture may be mounted in any position provided there is adequate room for ventilation. RIGGING Hanging Clamp It is importa
4. OPERATING INSTRUCTIONS Navigating the Control Panel Access control panel functions using the four panel buttons located directly underneath the LCD
Menu Map Menu 1-AddressWhen navigating the menu: Use the “UP” button to move up. Use the “DOWN” button to move down.Use the “ENTER” button to mo
Menu Functions MENU OPTION DESCRIPTION 1-Address Set the DMX address for the fixture. 2-Reset Reset the fixture. 3-Operation Select operating mode:
TO CHANGE THE CHANNELS SETTING: 1) Press the <MENU> button. 2) Scroll up or down until <8-Channels> is displayed. 3) Press <ENTER>.
Master/Slave Mode (Master Sound, Master Auto): This mode will allow you to link up to 32 units together without a controller. 1) Use standard DMX cab
DMX Channel Values in Advanced Mode CHANNEL VALUE FUNCTION 1 000 Ù 255 Pan 2 000 Ù 255 Tilt 3 000 Ù 255 Fine pan 4 000 Ù 255 Fine tilt 5 000
128 Ù 139 140 Ù 169 170 Ù 199 200 Ù 229 230 Ù 255 Reset No effect Sound Active 1 Sound Active 2 Random 12 000 Ù 009 010 Ù 019 020 Ù 029 030 Ù 039 040
TABLE OF CONTENTS 1. BEFORE YOU BEGIN...
DMX Channel Values in Basic Mode CHANNEL VALUE FUNCTION 1 000 Ù 255 Pan 2 000 Ù 255 Tilt 3 000 Ù 014 015 Ù 029 030 Ù 044 045 Ù 059 060 Ù 074 075
General Troubleshooting Applies to Symptom Solution(s) Lights Foggers & Snow Controllers Dimmers& Chaser Auto shut off Check fan thermal swit
Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.) Support (Email): [email protected] Telephone: (954) 929-1115 - (Press 4) F
General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing f
Technical Specifications WEIGHT & DIMENSIONS Length...
1. BEFORE YOU BEGIN What is included ¾ 1 x Q-Spot 152™ ¾ 150W HTI Lamp ¾ 5 additional metal gobos ¾ Power Cord ¾ Warranty Card ¾ User Manual Unp
Contact Us World Wide General Information Chauvet Lighting 3000 North 29th Court Hollywood, FL 33020 voice: 954.929.1115 fax: 954.929.5560 toll free
2. INTRODUCTION Features • 8 or 12-channel DMX-512 moving yoke • Pan: 540° / tilt: 270° • Variable strobe/shutter/dimmer • Color wheel 9 colors +
Product Overview Head Arm Base Control Panel Focus Adjust DMX Input Easy Controller Input (sold separately, re
3. SETUP Lamp You will need to install a lamp prior to the initial operation of the fixture. A 150W HTI lamp is included. Warning! When replacing th
LAMP ALIGNMENT HOW-TO Often, after a new installation of a lamp, you will find that there is an uneven field of light or what is referred to as a hot
Replacing Gobos Figure A Figure B 1) Remove the four screws indicated in figure A to remove the bottom of the head. 2) Remove the glue from the gobo
Comments to this Manuals